Http:// In this video I am showing shower drain installation ( when using pan-liner and tiling shower floor) and p-trap installation. I am also replacing rotten subfloor section with new plywood.
How to Install an Outdoor Shower | how- tos. Choose the Pipe and the Valve. Pipe is the first thing to consider when it comes to planning an outdoor shower.
How to Assess Your Furnace for Replacement; How to Install a Hybrid Water Heater; Drains Demystified: Dealing With Grease and Oils; 5 Creatively Fun DIY Wine Storage Ideas! Kitchen Island Cooktops: the Good, the Bad, and the. 50plus how to install electric shower. Plumbing Step 1: Start by mounting the shower unit in the required position. Mark the fixing points using the template supplied by the manufacturer or use the backplate if. Enter your model number above to make sure this fits. Constructed from high quality materials to ensure durability and reliability; WingTite design; Replaces leaky shower drain; WingTite shower drain is perfect for limited. DIY Network's Ed Del Grande, from Ed the Plumber, demonstrates how to install an outdoor shower on DIYNetwork.com. Installling a shower drain and waste pipe is a crucial part of constructing a new bathroom shower: The shower drain and waste pipe carry waste water away from the shower pan, helping to prevent unwanted odors in the home.
If the area temperature goes below freezing, assume that the pipe will freeze, and design the shower so the lines can be blown out or drained. Usually a combination of piping is used for an outdoor shower. Next, decide the type of shower valve to use. Most of the time, an outdoor shower is going to have cold water running to it, so although a traditional indoor shower mixing valve can be used, this is necessary only if hot and cold water will be used in outdoor shower.
The plumbing and wiring involved in installing. Ensure that wiring and plumbing are properly installed. Connect the. wiring at the consumer unit requires a competent person under the Part. P building regulation. Always turn off the electricity when making connections. Electric showers are economical to run and provide hot water on demand. Using an electric shower can save up to a third of the water used for.
Electric showers are rated in. W) - the higher the wattage, the better the performance. An electric shower is relatively easy to install, requiring. If you plan to install a shower over an existing bath, your primary. The most convenient. If that. is not possible, make the connection in the loft and run the branch.
If you are building a new shower cubicle, you will need to consider. Step 1: Start by mounting the shower unit in the required position.
Mark the fixing points using the template supplied by the manufacturer. Step 2: Using a power drill fitted with a masonry bit of the appropriate. When drilling holes in ceramic tiles, stick a piece of masking tape. Step 3: Before you finally mount the shower unit, cut a piece of 1. Try to make neat clearance holes through the. Connect the pipe to the shower inlet.
Cut copper. pipe with a hacksaw - wrap a piece of paper around the pipe as a guide. Alternatively, use a pipe cutter. File the cut. ends to remove burrs. Ideally pipe runs should be concealed and, in. If the wall is a stud partition, it should be.
In a solid masonry wall, you could cut a channel. This type of work should.
Use. soldered joints in this situation, to minimise the possibility of a. Step 4: Inside the airing cupboard or loft, take.
Fit a stopcock (not a gate valve) to the end of the branch pipe, with. Alternatively, fit a miniature isolating valve to the branch pipe, close. Step 5: Turn off the main stopcock and drain the water from the pipe. Step 6: Fit the T- joint onto the rising main and hand- tighten the cap. Measure and cut a short length of pipe to connect the T- joint. Step 7: Assemble the component parts and tighten the nuts to make watertight. Test the plumbing.
Showers connected to the rising main must be protected with a double- check. This applies only if the handset can come into contact with used water.
Caution must be exercised when inserting double check valves in the. If unsure, contact a professional plumber. Step 1: Mount the sprayhead slider rail on the wall to one side of the. Check that there is enough room for the sprayhead to be.
Step 2: Connect the flexible hose to the sprayhead. An instantaneously heating electric shower requires a dedicated radial. We recommend that the circuit. Residual Current Device. Use 1. 0mm two- core- and- earth cable for the circuit, which must be protected. Miniature Circuit Breaker (MCB) or a 4. If there is no room in your consumer unit for a new circuit.
Electrical Wiring Regulations require all non- electrical metal components. For supplementary bonding, as it is called, use.
Connect bonding cable to pipework with purpose- made earth clamps and. Your. shower unit must also be bonded to the pipework, using the earth terminal. Please check the details of your product. Although an electric shower has its own on/off switch, there must be. The isolating. switch must be out of reach from anyone using the shower. The isolating switch for a shower must have a contact gap of at least.
If the isolating switch is to be situated inside the bathroom, use a. Step 1: Make a hole in the ceiling where the pull- switch is to be fitted. Screw a mounting board between the joists above the ceiling on which. Step 2: Run the circuit cable to the switch position and pass a loop. Then run. the cable on to the shower unit. You can run electrical cable inside plastic mini- trunking fixed to the. Alternatively, bury the cable behind the plaster.
One way is to pass the cable down between the studs of a hollow partition. For a solid wall, you would have to cut out a. In this case, it is safest to run. Step 3: At the switch point, cut the loop of cable and strip the ends. Fix the backplate of the switch in position. Cover the. bare earth wires with green and yellow sleeving and connect them to. E' terminal. Step 4: Connect the wires of the cable from the consumer unit to the.
Mains' terminals of the switch. Connect the wires of the cable to the. Load' terminals - red to 'L' terminals and black. N' terminals. Step 5: Strip the sheathing from the cable at the shower unit and connect. Red 'L'. (live), Black 'N' (neutral) and bare 'E' (earth). Cover the bare wires. PVC earth sleeving.
Strip about 1. 00mm (4in) of sheathing from a cable - slit it lengthways. Use a Part P competent person electrician to make the connection to.